Основная     О фирме     Продукция    Решения    Новости    Поддержка    Где купить?

Модули для семейства Mercury

1. E1 

E1 Specifications
-  Bit Rate: 2.048 Mbps ± 50ppm
-  Line Code: AMI/HDB3
-  Impedance: 120 ohm balanced or  75 ohm unbalanced
-  Connector: Terminal block (balanced)  or BNC (unbalanced)

Modules Available:

-  E1-4CB 4-port E1 I/O module, 120-ohm balanced 
-  E1-2CB 2-port E1 I/O module, 120-ohm balanced 
-  E1-4CU 4-port E1 I/O module, 75-ohm unbalanced 
-  E1-2CU 2-port E1 I/O module, 75-ohm unbalanced

2. A/µ card for T1 / E1 Conversion

A/µ card performs A-law/µ-law & signaling conversion on per DS0 channel.
With A/
µ card, Mercury can be configured to work as 5T1 to 4E1 converter.

3. POTS- FXS/ FXO

Modules
* 4 Ports FXS module or 4 Ports FXO module.
* A -Law or
m - Law coding.
* Signaling: Loop start.

4. POTS- 2W E&M/ 4W E&M

Modules
* 4 Ports 2W E&M module or 4 Ports 4W E&M module.
* A -Law or
m - Law coding.

POTS - Unique Feature

Eliminates Central Office / Exchange Terminal and FXO or E&M  I/F.
Remote Terminal Connects directly to E1(CAS,RS) port from the Switch.
No expensive V5.1 software upgrade required for Switch.

5. Data Port

· V35-3A         1-port V.35 I/O module
· V35-3B         2-port V.35 I/O module
· RS-530-3A     1-port RS-530 I/O module
· X.21-3A        1-port X.21 I/O module
· V.36-3A        1-port V.36 I/O module

-  DTE / DCE interface configurable.
-  Maximum data rate of 24 x64kbps for T1 or 31 x 64Kbps for E1.
Mapping to any sequential time slots in T1/E1.

6. X.50 Sub-Rate MUX and DACS 

SpecificatMUX-5C, MUX-4C, DACS-2C)
MUX-5C -   5 ports Sub-Rate MUX
MUX-4C -    4 ports Sub-Rate MUX
DACS-2C - 2 ports Sub-Rate DACS

Comply with X-50 Division 3 multiplexing
- Multiplexing multiple Sub-Rate data into single DS0.
- Physical ports RS232 I/F
- Data speed :2400, 4800, 9600, 19200
- Sync / Async mode

7. Router/Bridge Module

WAN Protocol: Sync PPP / RFC 1490
AUX Port : Sync PPP / Async PPP  
Routing Protocol: RIP V1/V2, Static Route.
-  Transparent Bridge (IEEE 802.1d)
-  NAT, Static IP Filter, DHCP Server(Future)
-   Ethernet Interface:10 base T
-  Software Upgrade: Flash download over TFTP
-  Management: Mercury craft port, TELNET, SNMP

8. Channelized Router Module

- Support up to 32 DS0 Channel PPP connection
- WAN Protocol: Sync PPP
- Routing Protocol: RIP V1/V2, Static Route.
- Ethernet Interface:10 base T
- Software Upgrade: Flash download over TFTP
- Management: Mercury craft port, TELNET, SNMP 

9. IDSL module

Specifications 
- 4 x IDSL per module.
- Operate with TAINET Jupiter 2560
- Line interface
   U interface confirm to ANSI T1.601,  ETSI TS 102 080, ITU-T G.961

Loop requirement: 
- 2 wire unconditioned twisted line

Service Rate: 
- Symmetrical Synchronous 64/128 Kbps

Operation Range:
   6 Km over 26AWG wire
   7.8 Km over 24 AWG wires

10. G.SHDSL

Specifications 
- Single G.SHDSL per module
-  Line interface : 
   RJ45 connector, G.991.2(B.4) 

Loop requirement: 
  
2 wire unconditioned twisted pair.

Service Rate: From 144k up to 2320K. 

Operation Range: 
    From 3.8km up to 6.9Km  (0.4mm/No noise condition) 

11. Fiber Optical Module

Features: 
- 4XE1 transmission capacity.
- Provide 1310nm(single mode) optical laser source.
- Provide 1:1 line protection for Redundancy
- Transmission distance up to 55 Km
- Provide Local and Remote loop-back testing for diagnostics
- Comply with G.821 for performance monitoring 
- Provide Alarm and Status indicators for status monitoring